V and W Series
Both the V and W series are effective to control
emissions in equipment using SCR and T2L circuits for compliance with FCC Part 15, Subpart J and EN55022, Level A, down to 150kHz
emissions in equipment using SCR and T2L circuits for compliance with FCC Part 15, Subpart J and EN55022, Level A, down to 150kHz
V Series
- Offers an N = 3 ("T") Line to Ground impedance to common mode and an N = 5 "Dbl. Pi") impedance for Line to Line differential mode interference
- Designed for susceptibility use when equipment impedance at RF frequencies is low
W Series
- Offers an N = 4 ("Dbl. L") Line to Ground impedance for common mode and an N=5 ("Dbl. Pi") impedance for Line to Line differential mode interference
- Designed for use when equipment impedance at RF frequencies is high
- Two stage construction provides excellent suppression at high frequencies
Ordering Information
Available Part Numbers
3VV1 | 3VW1 |
6VV1 | 6VW1 |
10VV1 | 10VW1 |
20VV1 | 20VW1 |
20VV6 | 20VW6 |
20VW7 | |
Specifications
Maximum leakagecurrent, each Line to Ground: | ||
@ 120 VAC 60 Hz | 0.5 mA | |
@ 250 VAC 50 Hz | .82 mA | |
Hipot rating (oneminute): | ||
Line to Ground | 2250 VDC | |
Line to Line | 1450 VDC | |
Operating Frequency: | 50 / 60 Hz | |
Rated voltage(max.): | 250 VAC | |
Rated Current: | 3A to 20A | |
20A models VDEapproved to 16 Amps | ||
Operating Ambient Temperature Range(at rated current Ir): | ||
-10°C to +40°C | ||
In an ambienttemperature (Ta) higher than +40°C the maximum operating current (Io) is calculated as follows: Io = Ir √(85-Ta)/45 | ||
Electrical Schematic
V Series
W Series (3, 6 & 10A)
W Series (20A)
Case Styles
V1 / W1 (3, 6 & 10A)
Typical Dimensions: | ||
Line/Load Terminals(4): | .250 [6.3] with .07 [1.8] Dia. hole | |
Ground Terminal(1): | .250 [6.3] with .07 x .16 [1.8 x 3.8] slot | |
Mounting Holes (2): | .188 [4.75] Dia. | |
V1 / W1 (20A)
Typical Dimensions: | ||
Line/Load Terminals(4): | .250 [6.3] with .07 [1.8] Dia. hole | |
Ground Terminal(1): | .250 [6.3] with .07 x .16 [1.8 x 3.8] slot | |
Mounting Slots (4): | .250 x .156 [6.35 x 3.96] Dia. | |
V6 / W6
Typical Dimensions: | ||
Terminals (5): | 8-32 Torque 18 lbf-in. [2.03 N-m] max. ±2[..22] | |
Mounting Slots (4): | .250 x .156 [6.35 x 3.96] Dia. | |
VW7
Typical Dimensions: | ||
Load Terminals(2): | .250 [6.3] with .07 [1.8] Dia. hole | |
Ground Terminal (1): | .250 [6.3] with .07 x .16 [1.8 x 3.8] slot | |
Line Inlet (1): | IEC-60320-1 C20 | |
Threaded Inserts (2): | 6-32 x 1/4 | |
Recommended Panel Cutout
Case Dimensions
Part No. | A | B | C | D | E |
(max.) | (max.) | (max.) | ±.015 | (max.) | |
± .38 | |||||
3VV1, 3VW1 | 3.36 | 1.82 | 1.28 | 2.375 | 2.78 |
85.3 | 46.2 | 32.5 | 60.33 | 70.6 | |
6VV1, 6VW1, 10VV1, 10VW1 | 3.86 | 2.08 | 1.53 | 2.938 | 3.34 |
98.0 | 52.8 | 38.9 | 74.63 | 84.8 | |
20VV1, 20VW1 | 5.23 | 3.38 | 1.53 | 3.75 | 4.20 |
132.8 | 85.9 | 38.9 | 95.25 | 106.7 | |
20VV6, 20VW6 | 5.34 | 3.38 | 1.53 | 3.76 | 4.20 |
135.64 | 85.9 | 38.9 | 95.5 | 106.7 | |
20VW7 | 5.65 | 3.12 | 2.29 | ||
143.51 | 79.25 | 58.17 | |||
