Guang Dong Jiu Zhou centrifugal fan /HP exhaust fan
this serizes adopt centrifugal structure,classified by outer casing impeller, the serizes can be divided into two types. one is aluminium alloy type and rolling plate stamping type.featured by little weight, new pattern and big air flower and low noisr, this serizes are used in some industry devices to blow air,such as smelting,diesel,vaporization,matching ,kitchen equipment, pneumatic compression facilities.boilers, plastic machinery, but places using the fans shouldn't contain flammable,explosive ,toxic and corrosive gases, with the temperature no higher than 80℃.
.
Tai Wan Quan Feng centrifugal fan
1, performance is goodand remarkable,, quality is reliable . it can be used in the desert and at an altitude of 4000 meters , high temperature resistant, low temperature.
2, low noise, using high-tech low noise transmission directly, inside muffler can reduce the noise during operation.
3, high reliability, alnost noneed for maintenance : in addition to the impeller which connected directly to the motor, there is no other moving parts, impeller gearless drive belt. So the reliability is higher.
4, no oil pollution: due to the impeller and other components not contact, lest the lubrication.
5, Taiwan high pressure fan pressure stability, high mechanical precision, run some parts after extreme precision balance design, testing, calibration, so the vibration rate is extremely low, application instances prove that water treatment, electroplating processing, mixing evenly, the waves roll highly consistent. Shanghai hao crown electromechanical equipment co., LTD., direct selling Taiwan the wind fan, explosion-proof fan, middle fan, high pressure blower, the wind pressure ring fan, centrifugal fan, the air blower, pu fan, vortex air pump, the gas ring vacuum pump, all the wind pressure blower fan on high-end products in the industry, is China's performance is higher than similar products, all the wind high-pressure blower and the use of special materials:
One, the whole high pressure fan blades of the wind, the wind cover all adopt the world's most hard ADC12 materials, equivalent to the Mercedes wheel rims equivalent material.
2, all the wind high-pressure blower bearing with high speed, high temperature resistant import bearing, in the case of 50 hz, 2800 revolutions per minute, in the case of 60 hz 3450 r/min, no lubrication, maintenance free. Long-term support 24 hours operation, stable and reliable performance.
3, all the wind high-voltage fan out tuyere are device built-in sound attenuation, so as to achieve lower noise.
Four, the high pressure fan 1.1 KW wind the following models can be used in total pressure.
Five, the whole high pressure fan wind pressure stability, through the application instances prove that water treatment, electroplating processing, mixing evenly, the waves roll highly consistent.
Six, full wind high-pressure blower under the same power, the same pressure, flow rate is greater than the similar products.
Seven, the wind pressure fan wind cover adopts chip heat dissipation design, equivalent to a motorcycle engine cooling device, greatly reduces the temperature at which the fan operation.
Eight, all the wind high-pressure blower bearing pre design principle of two bearings in the blades of the fan at the rear end of the front end and the motor, to achieve the best configuration of dynamic balance, and conducive to heat dissipation.
(the reason is that: the wind leaf front have a heat sink for cooling, and then the bearing work under fan with cooling fans, to maintain the bearing long-term work under low temperature.)
Nine, all the wind high-pressure blower adopts special shockproof foot pedestal design, thereby significantly reducing vibration generated by the fan operation.
Ten, all the wind high-pressure blower economic and energy-saving. Under the same power, equivalent stress, equivalent flow, the wind pressure fan current less than other similar products.
Listed, the wind is a new generation of high pressure blower comprehensive national regional agents to recruit hot, welcome consulting agent to negotiate.
All the wind blower performance characteristics:
1, easy to install
The wind pressure blower can install at the place of use at any time for compressed air or used in time. And can any installation of horizontal or vertical direction.
2, the structure solid
All the wind with ADC12 aluminum alloy casting, high pressure blower ontology is different from the general iron shell or AC10 blower of aluminum alloy, ADC12 material and Mercedes wheel drum same material, more strong and durable.
3, high reliability
In addition to the impeller, the wind no other moving parts, high pressure fan connected directly to the motor and impeller, gearless or drive belt, thus high reliability, almost maintenance free.
No oil and gas, no pollution, the impeller rotates, not contact with any missing, no lubrication, so can guarantee one hundred percent no oil and gas.
4, low vibration
Wind pressure blower parts all use, processing and testing equipment imported from Japan, Germany, run some parts have been extremely precise balance of design, testing, calibration, so the vibration rate is very low.
2, low noise, using high-tech low noise transmission directly, inside muffler can reduce the noise during operation.
3, high reliability, alnost noneed for maintenance : in addition to the impeller which connected directly to the motor, there is no other moving parts, impeller gearless drive belt. So the reliability is higher.
4, no oil pollution: due to the impeller and other components not contact, lest the lubrication.
5, Taiwan high pressure fan pressure stability, high mechanical precision, run some parts after extreme precision balance design, testing, calibration, so the vibration rate is extremely low, application instances prove that water treatment, electroplating processing, mixing evenly, the waves roll highly consistent. Shanghai hao crown electromechanical equipment co., LTD., direct selling Taiwan the wind fan, explosion-proof fan, middle fan, high pressure blower, the wind pressure ring fan, centrifugal fan, the air blower, pu fan, vortex air pump, the gas ring vacuum pump, all the wind pressure blower fan on high-end products in the industry, is China's performance is higher than similar products, all the wind high-pressure blower and the use of special materials:
One, the whole high pressure fan blades of the wind, the wind cover all adopt the world's most hard ADC12 materials, equivalent to the Mercedes wheel rims equivalent material.
2, all the wind high-pressure blower bearing with high speed, high temperature resistant import bearing, in the case of 50 hz, 2800 revolutions per minute, in the case of 60 hz 3450 r/min, no lubrication, maintenance free. Long-term support 24 hours operation, stable and reliable performance.
3, all the wind high-voltage fan out tuyere are device built-in sound attenuation, so as to achieve lower noise.
Four, the high pressure fan 1.1 KW wind the following models can be used in total pressure.
Five, the whole high pressure fan wind pressure stability, through the application instances prove that water treatment, electroplating processing, mixing evenly, the waves roll highly consistent.
Six, full wind high-pressure blower under the same power, the same pressure, flow rate is greater than the similar products.
Seven, the wind pressure fan wind cover adopts chip heat dissipation design, equivalent to a motorcycle engine cooling device, greatly reduces the temperature at which the fan operation.
Eight, all the wind high-pressure blower bearing pre design principle of two bearings in the blades of the fan at the rear end of the front end and the motor, to achieve the best configuration of dynamic balance, and conducive to heat dissipation.
(the reason is that: the wind leaf front have a heat sink for cooling, and then the bearing work under fan with cooling fans, to maintain the bearing long-term work under low temperature.)
Nine, all the wind high-pressure blower adopts special shockproof foot pedestal design, thereby significantly reducing vibration generated by the fan operation.
Ten, all the wind high-pressure blower economic and energy-saving. Under the same power, equivalent stress, equivalent flow, the wind pressure fan current less than other similar products.
Listed, the wind is a new generation of high pressure blower comprehensive national regional agents to recruit hot, welcome consulting agent to negotiate.
All the wind blower performance characteristics:
1, easy to install
The wind pressure blower can install at the place of use at any time for compressed air or used in time. And can any installation of horizontal or vertical direction.
2, the structure solid
All the wind with ADC12 aluminum alloy casting, high pressure blower ontology is different from the general iron shell or AC10 blower of aluminum alloy, ADC12 material and Mercedes wheel drum same material, more strong and durable.
3, high reliability
In addition to the impeller, the wind no other moving parts, high pressure fan connected directly to the motor and impeller, gearless or drive belt, thus high reliability, almost maintenance free.
No oil and gas, no pollution, the impeller rotates, not contact with any missing, no lubrication, so can guarantee one hundred percent no oil and gas.
4, low vibration
Wind pressure blower parts all use, processing and testing equipment imported from Japan, Germany, run some parts have been extremely precise balance of design, testing, calibration, so the vibration rate is very low.
