Fast Drying Automotive Repair 2k Topcoat Paint with a reddish shade
2K Topcoat, B215 Medium Yellow, An orange yellow with a reddish shade, good opacity.
Quick Detail:
Product Type |
Single-step series of two-component paint pigment concentration with a hardener and thinners, after construction was a bright light and can withstand strong finish |
Purpose |
Polished, completely dry, in good condition original paint, old paint surface and intermediate paint surface. |
Substrate |
The old paint and all kinds of mediun paint,primer is surface have been hardened and abraded Sand with 600-800#grit paper wet or 400-600# grit paper dry |
Mixing Ratio |
B215 Medium Yellow 100parts 281 Standard Drying Hardener 50parts Thinner 10-20parts |
Notice |
1, read the instructions before construction; 2, with the former the paint and hardener ratio adjusted as required, how much with how much Stir used within 6 hours run out; 3, the construction process to keep dry and clean, non-contact with water, acids, alcohols, bases, etc.; rear drums with paint hardener must Gaiyan avoid jelly scrapped; 4, during the construction and dry, shall not be greater than 85% relative humidity, |
Shelf Life |
18months if stored in its original sealed cans at 20 |
Packing |
1liter , 3.75 liter or 5 liter can |
Description:
This high quality 2K acrylic solid-colour paint is designed for high-grade sedan and business car. It’s specially used in the low temperature coating line of top-paint coating and mending. It features high gloss, high hardness and full paint film. Easy to apply, it is durable and won’t fade easily.
Specifications:
Viscosity : 130150S (spray-4 cups)/ 25
Ingredients: hydroxy acrylic resin, pigment, auxiliary agent, solvent.
Colour: 2K one coat, all kinds of autobodies, full colour range, colours can be customized.
Application Details:
(1) Application Primer
Remove the oil and grease away from the old paint or original paint. Apply HUATONG middle-coating baking paint and buff it with 600-800-sieve wet sand paper and then blow it dry. Otherwise, any water content left in the pits would affect the quality of the paint.
(2) Application Content:
Mixing Proportion: solid-colour paint : hardener: thinner=2: 1: 0.8~1 (Make a proper thinner proportion according to different temperatures)
Spray Viscosity: 17S(spray-4 cups)/25
Dilution: Add in 20-50% thinner according to the temperature (For local repairs, use the standard or quick-dry hardener or thinner; for whole car coating, use the standard and slow-dry thinner according to the termperature).
Hours of Use: approx. 6 hours at 25, (use 2K standard hardener);
Spray Pressure:4-5 Pa ;
Nozzle Diameter: gravity type 1.2~1.5mm
Suction type 1.4-1.6mm
Spray Method: Apply 2-3 coats to get a 45~60μm;
Waiting Interval: Adjust spray intervals according to the temperature. The interval takes 10-15 minutes at 20. After all sprays, wait 15-20 minutes before baking.
Tool Cleanings: Clean the tools with the thinner shortly after use.
Drying Time: 8 hours at 25, air dry needs 3 days to get cured completely, if baking at 80 for 30 minutes or baking at 70 for 45 minutes, then it needs 90 minutes to get cured completely.
(3) Reapply: For the treatment of small grains and sagging, buff them with 2000-grit sand paper after they’re completely cured and then polish them with polish wax.
Precautionss:
Add tie water in the proportion of 1: 1 into the paint left beind inside the junctions and spray gun and then spray the paint to the junctions.
As the two-component top coat would react with water, there should never be any water content i