100watt LED Driver 36V / LED Power Supply Waterproof 100W CEN-100-36
CEN Series Features (60~100W Single Output with PFC):
1. Universal AC input (up to 295VAC) / Full range
2. Protections: Short circuit / Over current / Over voltage / Over temperature
3. Built-in active PFC function
4. IP66 design
5. Meet 4kV surge immunity level (IEC61000-4-5)
6. Class 2 power unit / Pass LPS
7. Cooling by free air convection
8. Suitable for dry, damp, and wet location
9. Suitable for LED lighting and moving sign applications
10. 3 years warranty
CEN-100 Series Features:
1. Universal AC input / Full range (up to 295VAC)
2. Protections: Short circuit / Over current / Over voltage / Over temperature
3. Output voltage and constant current level adjustable
4. Built-in active PFC function
5. IP66 design for indoor or outdoor installations
6. Class 2 power unit
7. Cooling by free air convection
8. 100% full load burn-in test
9. High reliability
10. Suitable for LED lighting and moving sign applications
11. Compliance to worldwide safety regulations for lighting
12. Suitable for dry / damp / wet locations
13. 3 years warranty
CEN Series Power Supplies:
CEN-60 Series, CEN-75 Series, CEN-100 Series
Quick Details of CEN-100 LED Power Supply:
| CEN-100 Series | ||||
| Model No. | Output | Tol. | R&N | Effi. |
| CEN-100-20 | 20V, 0~4.80A | ±10% | 2.0V | 88% |
| CEN-100-24 | 24V, 0~4.00A | ±10% | 2.7V | 89% |
| CEN-100-30 | 30V, 0~3.20A | ±10% | 3.0V | 90% |
| CEN-100-36 | 36V, 0~2.65A | ±10% | 3.6V | 90% |
| CEN-100-42 | 42V, 0~2.28A | ±10% | 4.0V | 90% |
| CEN-100-48 | 48V, 0~2.00A | ±10% | 4.6V | 91% |
| CEN-100-54 | 54V, 0~1.77A | ±10% | 5.0V | 91% |
Specifications of CEN-100:
| Model No. | CEN-100 | |
| AC input voltage range | 90~295VAC; 127~417VDC | |
| AC inrush current (max.) | Cold start, 45A at 230VAC | |
| DC adjustment range | ±10% rated output voltage | |
| Current adjustment range | 65%~100% | |
| Over current protection | 95%~110% constant current limiting, auto-recovery | |
| Over voltage protection | 110%~135% rated output voltage | |
| Over temp. protection | Shut down o/p voltage, re-power on to recover | |
| Setup time | 500ms at full load and 230VAC, no hold up time | |
| Withstand voltage | I/P-O/P: 3.75kVAC, I/P-FG: 2kVAC, O/P-FG: 1.5kVAC | |
| Working temperature | -30~+70Celsius (refer to output derating curve) | |
| Safety standards | UL8750, UL879 (except for CEN-100), TUV EN61347-1, EN61347-2-13, PSE J61347-1, J61347-2-13 approved | |
| EMC standards | EN55015, EN61000-3-2 class C , EN61000-3-3, EN61000-4-2,3,4,5,6,8,11, EN61547 | |
| Connection | Input | UL rated, SJTW 18AWGx3C (30cm) |
| Output | UL rated, SVT 18AWGx2C (30cm) | |
| Dimension (LxWxH)(mm) | 185x 62.5x 40.5 | |
NOTE:
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. Please refer to "DRIVING METHODS OF LED MODULE".
6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains.
CEN-100 Series Datasheet:
