Characteristics
· Transparent I/O System, no programming required
· Not need internet, no third party cell, no monthly fees
· You have full control over your own carrier
· Real time status feedback from the remote site
· Fast installation and easy setup
Parameter:
· Input: 8 isolated digital active inputs (passive input customize)
· Output: 8 isolated relay passive contact outputs, contact load 5A@220V AC, 5A@30V DC.(active output customize)
· Protocol: Modbus RTU
· Collocated with a wireless data module whose transmitting distance is about 2km-3km; the working frequency 433MHz (400-470MHz); RF power: 1W; Receiving sensitivity: -123dBm
· Receiving current:<50mA; transmitting current: 600mA
· Power supply: DC 9V-36V
· Dimension: 145mm*90mm*40mm
Parameter | |
Power output: | 1W or 100mW version |
Power supply: | 9V-30V (usually choose 24V DC or 12V DC) |
Control distance: | 3km or (1km version) |
Baud rate: | 1200bps |
Receiving sensibility: | -123dBm@1200bps, -118dbm(9600bps) |
Networking | |
Networking: | Point to point and point to multipoint |
Port Description | |
Input: | 8 active DI (passive customized) |
Output: | 8 relay passive outputs, contact max load AC250V/5A,DC30V/5A (Active output 0-5V customized) |
Communication port | RS485 (wireless RS485 customize) |
Current | |
Transmit current: | <600mA (or 100mA version) |
Receiving current: | <50mA (or 20mA version) |
General | |
Frequency: | 433MHz, 400, 450, 470 or other band |
Channel No: | 16 channels,can change via DIP switch |
Physical Properties | |
Dimension: | 145×90×40(mm) |
Antenna Connector: | SMA,vehicle antenna with 1.5m cable |
Temperature: | -35℃~+75℃( industrial) |
Mounting method: | Standard 3.5 inch industrial guild rail |
Application area:
· Lighting Control Systems
· Wireless Pump Control
· Wireless Valve Actuation
· Conveyor Control
· Grain Augers
· Engine Control
· Tank Level Monitoring
· PLC Activation
· SCADA
Application Diagram
About the DIP Setting
1) Outer(right side) DIP 1-4 are used for channel setting. Please check the following definition:
Channel No. | DIP Setting | Channel No. | DIP Setting | Channel No. | DIP setting | Channel No. | DIP setting |
1 | 1234 | 2 | 1234 | 3 | 1234 | 4 | 1234 |
5 | 1234 | 6 | 1234 | 7 | 1234 | 8 | 1234 |
2) Outer(right side) DIP 5-8 are used for mode setting. Please check the following definition
DIP | Status | Function | Remarks |
5 | OFF | With feedback | |
ON | No feedback mode | remote side DI, this side only DO | |
6,7 | OFF,OFF | 1 to 1 control | Master set ID to X, Slave module's ID set to X (ie. master ID1, slave ID1. remember set ID the same) |
6,7 | ON,OFF | 1 to 2 slaves control | Master set to ID1, 2 slave modules' ID set to 1 and 2 respectively |
6,7 | OFF,ON | 1 to 4 slaves control | Master set to ID 1, 4 salve modules' ID set to 1, 2, 3 and 4 respectively |
6,7 | ON,ON | 1 to 8 slave control | Master set to ID 1, 8 slaves' ID set to 1, 2, 3, 4, 5, 6, 7 and 8 respectively |
8 | OFF | Slave mode | |
ON | Master mode |
