Integrity promise Connaught, intentions to do everything.
Export manufacturer
Passed Certifications - ISO9001:2015
TN Product tested by National Coal Science Institute and Provincial Quality Inspection Center
Deep groove ball Bearing. or single row radial, ball bearings, used as conveyor roller bearing. It usually consist of a pair of rings, a retainer, a single row of steel balls. Its structure is simple, easy to use, non-separable, It is the most widely used type of bearing. This type of bearing is mainly used to bear radial load, but it can also bear a certain amount of axial load in either direction.
We are a manufacture specialized in producing conveyor roller bearing. bearings also have a clearance value. This provides the bearing room for expansion between the bearing races and will add a small amount of play between the two rings. large clearance C3/C4 usually used in mining machine.
| C1 | Smaller than C2 |
| C2 | Smaller than Normal |
| CN | Normal |
| C3 | Greater than Normal |
| C4 | Greater than C3 |
Application
Mining machine, conveyor machine, Engineering Machinery, Agricultural Machinery, Construction Machinery, textile, chemical, auto motor, Transportation Vehicles, General industrial Equipment, etc.
Catalog of Deep groove ball bearing
Professional brings quality, detail creates success
XKTE bearing's most fundamental difference is:
The other manufacturers make products considering the price cheap, but we make products considering the service life. Each of the idler roller bearings we produce is fully implemented in the national standard. XKTE bearings exist for their quality and brand. You can deny our price, but you can never find out our products' defects in quality. XKTE conveying machinery bearing, a big brand, is worthy of your trust.
First, the identification of the bearing
Formal manufacturers use laser engraving. The stamps are deep, have significant dents with hand touch, good-looking, with no breakpoints, and are never disappeared. This obviously improves the bearing grade.
The use of bearing retainer
Bearing retainer selection is very important. Because once too much dust stuck into the bearing, the retainer will be first worn. If the bearing retainer is broken, the bearing will be directly broken. Imported bearings use big rivets to thicken retainers. XKTE bearing is completely in accordance with the process of imported production, so each piece of ours is made to a high quality, and guaranteed to operate for thirty thousand hours.
Selection of nylon retainer
Nylon retainer bearing is often used in the mine. Nylon retainer has better anti-stuck performance and wider range of temperature than iron retainer. In the underground its anti-static performance is also better. To get safety certificate for coal mining products must use nylon retainer KA bearing. The selection of nylon retainer is crucial to KA idler roller bearing, while the material of nylon retainer must be pure and has enough toughness and strength, because the retainer will get very soft if it is made of bad material or mixed material, thus to make no anti-stuck performance within the bearing.
The ring is the main part and the important part of the idler roller bearing. Best idler roller bearing has deep groove ball, and large clearance. But deep groove doesn't mean to dig the channel with a simple way of enlarge the steel ball. The thickness of the bearing is certain, so to get the ball big and the groove deep will shorten service life. Our XKTE bearing uses way of thickening ring to get the standard of deep groove and large clearance, improves the anti-stuck performance, and effectively increases the service life.
Bearing material and hardness
Good idler roller bearing must be made of bearing steel, named "High Carbon Chromium Bearing Steel (Fully quenched class) GCr15". At present the standard hardness of idler roller bearing is 60-65 degree, while hardness of ring is 61-62 degree, andball is 64-65 degree.
The simple way to identify idler roller bearing is to see if its hardness is over 60 degree, because only bearing steel can get over this degree.
Grease selection of roller bearing
Many customers ignore this most critical point. The thirty-thousands-hours operation is a very long term. This has to be guaranteed by enough quality and quantity grease. And this should also be taken into account of working in different seasons.
Special note: please choose special high temperature grease if working environment is over 120 °C for long time or low temperature grease if it below -20 °C.
Reference:
The test and application after the instalation of the conveyor bearing
The instalation of the conveyor bearing must be done in dry and clean conditions. Before the instalation, we must check whether the outer track and retainer of the conveyor bearing have any quality problem, and make sure polishing the burr produced when not being processed subtly of the conveyor bearing with sand paper.
Then wash over the burr and sand in the conveyor bearing with kerosene or solvent detergent. And after drying it, we add grease into the conveyor bearing, thus we have finished the preparing work before the instalation.
Next we will adjust the clearance of the conveyor bearing, and after, we check the service behavior of the conveyor bearing´ work. We can use our hands to rotate the principle axis to finish the job.
But it is different and more complex to instal the conveyor bearing to the big machinery. It must start the machine to check whether the device runs normally after installing the conveyor bearing. At this time, the temprature of the conveyor bearing begins increacing, if the temprature continues increasing after the conveyor bearing runs for one hour, it explains that it exists problem in the instalation, we must stop running the machine and check it over. After excluding all the problems, we start the machine again, and after the rotate speed of the conveyor bearing achieving the rule for a while, if we find the temprature of the conveyor bearing stays stable, and do not appear noise, this shows that the conveyor bearing and the whole machine can run normally.
Other Products
Package:
1. Industrial packaging : Single box + outer carton + pallets
2. Neutral Packing:
Tube package + outer carton + pallets
Tube package + middle box + outer carton + pallets
3. As buyer's request
Payment methods:
1) TT, 30% deposit , 70% before shippment.
2) L/C at sight. (high bank charge, not suggest , but acceptable )
3) 100% Western Union in advance. (specially for air shipment or small amount)
Shipment | For small orders,we send by express UPS,DHL,FEDEX, or EMS with Thracking number. For big quantity, we will ship by air or by sea. |
Delivery date | Normally stock within 3-7 days. Bulk quantity within 30 days. |
Payment terms | T/T L/C |
2. For small amount, we accept Western Union | |
Samples Policy : | Small sample free and bulk sample cost needed and freight collected. We will reduct this part expense from the total value when place order. |
Started 2006, We are a manufacture of industrial Bearing in Liaocheng Shandong, concentrates on manufacturing industrial bearing, mainly used in conveying equipment, machinery, textile, chemical, auto motor and so on. Especially bearing for conveyor, which make us become one of well-known enterprise in China. We have 26 production lines, mainly produce deep groove ball bearing, spherical roller bearing, TN Nylon cage bearing and sealed bearing.
All of Our products are made of Chrome Steel GCr15, with grinding groove and superfinishing technology. Supply ability is about 20000 Pieces / per Day. We have our own brand XKTE, and we can also provide OEM service.
FAQ:
I couldn't find a design to fit my application in your catalog. Can you help me design a bearing?
Yes, technical expertise is available to assist you with engineering design for custom products. Available options include, but are not limited to, custom rings, retainers, balls, shields, lubricants, and packaging. We look forward to working with you to satisfy your rotary motion requirements.
What causes bearing noise?
Bearing noise is a function of both the bearing and the way it is used. Some external factors that affect bearing noise include lubricant type, excessive bearing load, and improper installation. Once the abnormal noise occurred, you can contact our engineers, we will help you find the reasons and provide the appropriate solutions.
What is the difference between using a shield or a seal as a ball bearing closure?
Shields or seals are often installed to retain lubricant and to prevent contamination from entering the bearing. While a shield contacts the outer ring and does not come in contact with the inner ring, the seal generally comes in contact with both the inner and outer rings. Torque or drag is lower with a shield than with a seal. Alternately, the seal provides a higher degree of protection from contamination. Shields and seals are available in a variety of materials and configurations.
XKTE developed a serious of sealing methods for different applications. Please contact a XKTE engineer for technical assistance with any special requirements.
Why choose us ?
1. professional commitment to conveying machinery bearing, leading enterprise of conveyor
machinery bearing in China.
2. With background of about 10 years
3. Strict Inspection ,and the best quality price with reasonable price bearings provided .
4. OEM service provided.
5. Delivery products from our factory warehouse , short delivery time.
86-15688862750
02 at xinkaite.com
www dot xinkaite dot com
