DST(Drill Stem Testing) Tools 5" Hydraulic Circulating Valve
Product model: Hydraulic Circulating Valve
Size: 5", 3 7/8", 4 5/8", 5.00"
Standard: API
Service:H2S, CO2
Usage:Drill stem testing
Working condition: High pressure high temperature(HPHT)
Working pressure: 10000psi ~ 15000psi
Condition: New
Application: Oil well testing
Briefly Introduction
The hydraulic circulating valve serves as a bypass around the packer or as a circulating valve to circulate a well after testing.
When run below a closed valve, the tool serves as a bypass around the packer and helps relieve pressure buildup below the closed valve when it is stung into a production packer.
When run above a closed valve, the tool can be used as a circulating valve when the workstring is picked up.
Features and Benefits
• Permits passage of wireline tools through its full-opening bore
• Requires no pipe rotation to operate
Operation
Bypass ports close when weight is set down and reopen when weight is
lifted.
A hydraulic metering system provides a 2 to 3-minute delay in closing after weight is applied. This delay allows either the RTTS packer to be set or the test string to be stung into a permanent packer before the bypass ports close. The ports reopen without a time delay.
During stimulation work, the latching piston adds a downward force on the circulating sleeve to help keep the valve closed.
Operation of the valve is the same whether it is used as a circulating valve or as a bypass. No torque is required. Weight is applied to close the tool, and the workstring is picked up to reopen it.
Specifications:
1. Halliburton type, all could change with Halliburton parts.
2. All equipments are produced according to API standard NACE MRO175-2002
Below are spec for you reference:
Nominal Tool Size in. | OD In (mm) | ID In (mm) | Thread Connections | Service Temperature °F(°C) | Length In (cm) | Stroke Length In (cm) | Tensile Rating lb(kg) | Working Pressure Psi (bar) | Flaw Area In2. (cm2) | Number of Ports |
3.00 | 3.06 (77.72) | 1.25 (31.75) | 21/4 CAS | 450 (204) | 79.80 (202.69) | 3.00 (7.62) | 134,000 (60782) | 15,000 (1034) | 1.27 (8.19) | 4 |
37/8 | 3.90 (99.06) | 1.80 (45.72) | 27/8 CAS | 450 (204) | 82.69 (210.03) | 3.00 (7.62) | 164,000 (74390) | 10,000 (689) | 1.17 (7.55) | 6 |
45/8 | 4.68 (118.87) | 2.25 (57.15) | 31/2 IF 37/ 8 CAS | 450 (204) | 83.76 (212.75) | 3.00 (7.62) | 261,000 (118389) | Burst 15,000 Collapse 14,000 (964.6) | 1.28 (8.26) | 4 |
5.00 | 5.03 (127.76) | 2.03 (51.56) | 37/8 CAS | 450 (204) | 83.76 (212.75) | 3.00 (7.62) | 261,000 (118389) | 15,000 (1034) | 1.28 (8.26) | 4 |
Here is the draft for your reference
Xi'an KINGWELL OILFIELD MACHINERY Co., Ltd. (KINGWELL), is a highly reputable supplier for oilfield equipment and services to Oil & Gas industries and provide complete solutions.
With over 10 years developing, we were developed from the beginning drilling service to manufacture factory who produce OCTG, DST tools and Solid control products.
Accordingly most innovative and reliable toolsKingwell set up a long-term science and technology cooperation, with xi'an petroleum University, daqing/ changqing oil&gas institute and jianghan machinery Research institute.
KINGWELL have experienced team, stronger enough to meet any challenge, we do believe honest is the base of business and cooperation, our aim is to build solid relationship with any part of honest. kingwell can provide highly efficient services to its clients resulting in accurate and timely deliveries at the best prices. Our products have been exported to Europe, American and Middle East.
Certifications
Kingwell is a CNPC & SINOPEC & BV certified company, having all the Quality Systems in place for design, planning, manufacturing and quality monitoring & traceability to ensure our products match the highest quality standards.
We test our products strictly according to the NACE MR 0175-2002 Standard and our quality assurance period is 12 months.
Certificates endorsed by DNV/BV/ABS and Documents we can supply with the shipments:
1. Pressure Test Certificate with Graph and time recorded.
2. Function Test
3. Rubber Products NACE Compliance
4. Material Mill Certificate and treatment characteristics
5. H2S Compliance
6. Service Manual
7. Parts Manual
8. Testing Procedures.
9. Open up type tool drawing for dressing purpose– if any.
Manufacturing Facility
Equipped with latest machining facilities like CNC 3-axis Turning centers, CNC 4-axis milling centre, high temperature heat treatment furnaces, Centre lathe machines, Deep Hole Drilling, Boring & Honing machines, our company could meet long term production target and be governed efficiently by well-qualified and experienced Board of Directors and Engineers.
Quality Systems
A well-established Quality System from Materials receipt to Products delivery ensures consistent quality at all levels of the activity. QMS Procedures & Measurements are tailored to establish high standards of Quality Assurance in the Operations. The Company maintains the 100% Traceability records as per API requirements &NACE MR 0175-2002 Standards and complies with all the legal, statutory and regulatory requirements.
1\Quality control of the raw material:
1)The selection of the raw material supplier:our raw materials mainly include alloy structural steel, stainless steel, non-ferrous metal alloy and high nickel alloy, etc, in the selection of the raw material suppliers, we would do the comprehensive assessment of the supplier strictly according to technical requirements .Most of our suppliers are the leading enterprises of the steel production in China and the special alloy are usually purchased from abroad to ensure a higher mechanical properties.
2) The acceptance & Inspection of the raw material:
Ultrasonic flaw detection for every piece of the steel.
Chemical composition analysis for every piece of the steel.
Mechanical performance test for every piece of the steel..
2\Quality control of the seals:
1) O Rings: 100% visual and dimensional inspection for every piece of the O-rings, 15% spot check for the size and hardness test of the o rings. As for the sealing and heat resistance properties of the o rings, we designed a special test device which is equipped with heating insulation equipment that can simulate the down hole temperature and pressure. At present, our fluorine can keep a good performance in the condition of 210 ℃, and 105 Mpa work pressure (maximum pressure ever reached 146).
2) Back-up ring: 100% visual and dimensional inspection for every piece of the back-up ring, as for the test of the sealing and heat resistance, we design and manufacture the special test device, equipped with heating insulation equipment to stimulate the down hole temperature and pressure for acceptance. At present, our company's high pressure back-up seal can keep good sealing performance and deformed a little in the condition of 210 ℃, and 105Mpa work pressure (maximum pressure ever reached 146). It can be used for many times.
3. Quality control of the spring: Apart from the conventional test of the raw material and size of the different springs that used in the tools, we specially designed a test device that equipped with heating preservation equipment to stimulate the down hole temperature and condition to test the spring performance.
4. Quality control of the spare parts processing:
1) Spare parts processing control:In strict accordance with the process and traceability requirements, a test, mark and record of dimension, geometric tolerance and for every piece and every procedure will be conduct.
2) Heat treatment quality control: We have two high temperature heat treatment furnaces that are mainly used for stainless steel and other special material heat treatment. For other materials, we entrust Baoji Petroleum Machinery Company Heat Treatment Plant to do the heat treatment.For the inspection of the heat treatment, we are equipped with the special inspection machine such as gantry hardness tester, digital universal tensile tester etc.
5. Quality control of the tool assembly and testing process
1) Test equipment: in addition to the conventional hydraulic test pump, tensile testing machine, we also have a pressure sensor and data acquisition system which can accurate and clear record each step of the test.
2) Technical documents: We have a test acceptance list for every tool test that clearly guides the each step of the test.
3) Assembly test: A special inspector will supervise the whole assembly process.
The following is the picture of Product Processing
Related products
We also provide accessories and other related products, which you can find in this website.
The following is the pictures about products accessories and some other related products
Product delivery
Payment:TT/LC:30% advance payment.70%before shipment
Warranty: Warranty period is 1 year after installation.
Origin: China
Minimum order: 1 set
Packaging: wood case or steel carton
Delivery Date: within 1-2 month(s) after receiving prepayment
Logo: KW, we can produce according to customer requirements.
Technical Documents: We can provide technical documents according to your requirements.
Additional service: Customers are served to test our products in our factory upon request.
Service
We believe in Customer delight, achieved by the supply of Quality Products & Services and Continual Improvement in our Manufacturing Processes for timely delivery at competitive prices. We work in a professional, competitive, and cost-effective manner consistent with the Customer requirement
