Open hole drill stem testing
5" x 10000psi Hydro spring tester
Multi-Flow Evaluator (MFE)
General
The MFE consists of three basic sections: indexing, delay, and sampling. Each of these sections will be described in detail below.
Indexing Section
The indexing section consists of three basic parts: Spline Mandrel, Spline Sleeve, and J-Pin, The function of the indexing section is to sequentially open and close the testing valve as the spline Mandrel (attached to the drill stem) is moved up and down. These motions may be repeated as many times as desired, each complete cycle opening and closing the testing valve. The indexing slot is in the Spline Mandrel and is shown in Figure Ⅱ. The Spline Mandrel is splined to the body of the tool and cannot rotate—it can move only in an axial direction, i.e., up or down. The J-Pin is securely fastened to the Spline Sleeve and rides in the index slot. The Spline Sleeve rotates freely through an 180°arc , but cannot move axially. We can see that as the Spline Mandrel moves up and down, the J-Pin follows the path of the index slot freely due to the rotation of the Spline Sleeve.To discuss the index slot in detail, consider the J-Pin as it moves around the index slot. The index slot is in the Spline Mandrel which is moved up or down by manipulation of the drill stem at the surface.
Delay Section
The "opening indication" mentioned above is incorporated into the delay system. The MFE incorporates a delay system similar to a conventional hydraulic tool: the hydraulic delay is effective when slacking down, but "disengaged" while picking up. The "opening indication" is a free fall of the drill stem that takes place the last inch of travel as the testing valve opens and is easily observed at the surface.
Sampler Section
The sampler section is a full flow-through type. All of the formation fluid passes through the sampler before entering the drill pipe .The sampler section incorporates a dual of seals and traps a sample at the end of the final flow period. The sample is trapped as the tool is closed for the final shut-in period. Note that the dual control valve is a safety factor- if one sample can be removed at the surface.
No Specification 5" 1 OD 127.5mm 2 Length(mm) 3102mm 3 Working pressure 70Mpa 4 Tensile strength(yield) 1868.8kN 5 Internal yield pressure 6 External yield pressure 22000psi 7 Torque strength 20000psi 8 Flow area 1200mm2 9 Service Environment Mud, crude oil, natural gas with H2S,apply to NACE MR0175-2002 10 End connections 3 1/2 IF. B X 3 1/2 IF.P(with crossover) 11 Service Temperature -20oF~+400oF
Specificatoin
Hydrospring Tester pressure testing chart
Testing equipment
DST tools testing preparation
ZZ TOP OIL TOOLS is the professional manufacturer for the drill stem testing tools and surface testing equipment. All the DST tools are conformed with NACE MR 0175 with traceability,and the DST tools can be worked in H2S & CO2 above 175 F and full H2S, also with the skilled and experienced engineers, we can design the drill stem testing tools as per customer's well condition. Moreover, we supply the training in our factory and operation instruction at the well site. The DST tools are exported to USA, Colombia, India, Pakistan, Iran, Brazil etc. and enjoy the good reputation from the customers.
To shorten the delivery time, we proceeded the DST Tools in stock:
Packer,circualting valve,select tester valve,APR N-valve,OMNI valve,Hydraulic Jar,Tubing string tester
1. Full bore Packer, 7" Casing, working pressure 70Mpa, Working Temperature 400F, Connection: IF, 4set
2. Tester valve, 5", Working pressure 105Mpa, Working temperature 400F, Connection CAS. BXP, 4 sets
3. Hydraulic Jar,5", Working pressure 105Mpa, Working temperature 400F, Connection CAS. BXP, 4sets
4. Rupture disk Circulating valve, 5", Working pressure 105Mpa, Working temperature 400F, Connection CAS. BXP, 4sets
5. Flowhead (surface test tree), 3 1/16", working pressure 70 Mpa. 1set
Should you have any interest or inquiry on the Drill stem testing tools, contact us freely.
