Polished Thinner Violet Topcoat Auto Paint 1K one coat for Automobile Repair
Topcoat Paint, A125 Violet, A purple mixing color normally used with blue mixing color to preduce a redded effect
Quick Detail:
|
Product Type |
A purple mixing color normally used with blue mixing color to preduce a redded effect. Accurate color, high gloss, high hardness, paint film, easy construction, durable fade. |
|
Purpose |
Polished, completely dry, in good condition original paint, old paint surface and intermediate paint surface. |
|
Substrate |
The old paint and all kinds of mediun paint, primer is surface have been hardened and abraded Sand with 600-800#grit paper wet or 400-600# grit paper dry |
|
Mixing Ratio |
A125 Violet 100parts Thinner 10-20parts |
|
Notice |
1, read the instructions before construction; 2, with the former the paint and hardener ratio adjusted as required, how much with how much Stir used within 6 hours run out; 3, the construction process to keep dry and clean, non-contact with water, acids, alcohols, bases, etc.; rear drums with paint hardener must Gaiyan avoid jelly scrapped; 4, during the construction and dry, shall not be greater than 85% relative humidity, |
|
Shelf Life |
18months if stored in its original sealed cans at 20 |
|
Packing |
1liter , 3.75 liter or 5 liter can |
Product Specification:
Viscosity:130S~150S(spray-4 cups) /25
Ingredients: Acrylic resins, pigments, additives, solvents and the like.
Colour: 1K one coat, all kinds of autobodies, full colour range, colours can be ustomized
Application Details:
(1) Application Primer
Remove the oil and grease away from the old paint or original paint. Apply HUATONG middle-coating baking paint and buff it with 600-800-sieve wet sand paper and then blow it dry. Otherwise, any water content left in the pits would affect the quality of the paint.
(2) Application Content
Mixing Proportion: solid-colour paint : thinner=2: 0.8~1 (Make a proper thinner proportion according to different temperatures)
Spray Viscosity: 17S(spray-4 cups)/25
Dilution: Add in 10-30% thinner according to the temperature.
Hours of Use: approx. 6 hours at 25
Spray Pressure:4-5 Pa ;
Nozzle Diameter: gravity type 1.2~1.5mm
Suction type 1.4-1.6mm
Spray Method: Apply 2-3 coats to get a 45~60μm;
Waiting Interval: Adjust spray intervals according to the temperature. The interval takes 10-15 minutes at 20. After all sprays, wait 15-20 minutes before baking.
Tool Cleanings: Clean the tools with the thinner shortly after use.
Drying Time: 8 hours at 25, air dry needs 3 days to get cured completely, if baking at 80 for 30 minutes or baking at 70 for 45 minutes, then it needs 90 minutes to get cured completely.
(3) Reapply: For the treatment of small grains and sagging, buff them with 2000-grit sand paper after they’re completely cured and then polish them with polish wax.
Precautionss:
Add tie water in the proportion of 1: 1 into the paint left beind inside the junctions and spray gun and then spray the paint to the junctions.
As the two-component top coat would react with water, there should never be any water content in all equipment, containers and spray guns.
If any fish eye is found during the spray, stop the application at once. Add 3‰ antiball water and anti-fisheye water into the rest paint and then restore spraying. Thus the fish eye could be removed easily.
In winter, when the temperature drops to 20 below, it is suggested not to adopt self-dry method. It’s the best to bake in the baking chamber.
