GH-GH-FS1 Digital Satellite Finder Meter Signal Finder
If you have always wanted a professional satellite finder meter but did not want to pay the BIG BUCKS ,
this is the meter for you. First Strike Meters are made for the professional but are easy for the Novice to
understand and use. No more searching through complicated menus to find the setting you need to change.
All parameters show on one screen making it easy for the user to modify any setting.
If you have always wanted a professional satellite finder meter but did not want to pay the BIG BUCKS ,
this is the meter for you. First Strike Meters are made for the professional but are easy for the Novice to
understand and use. No more searching through complicated menus to find the setting you need to change.
All parameters show on one screen making it easy for the user to modify any setting.
GH-FS1 quickly and easily finds even weak signals. Unlike the competitors meters,
you can do a sweep of the dish to find the signal.
Uses the same type display screen as cell phones so it can be read in direct sunlight.
Display screen has a switchable back light so your meter can be used in low light conditions.
GH-FS1 has a Global Data Bank that holds all the satellites in a separate data bank.
The meter also has a User Defined Data Bank that stores 100 satellites. Entries in the
Global Data Bank can be copied to the User Defined Data Bank and then easily edited to
fit your needs. The user can define new entries from the keypad.
The meter also has a User Defined Data Bank that stores 100 satellites. Entries in the
Global Data Bank can be copied to the User Defined Data Bank and then easily edited to
fit your needs. The user can define new entries from the keypad.
Meter never needs to be returned for re-calibration due to the unique calibration system
built in to the meter. Each time the meter boots up it automatically calibrates for optimum
performance so you can align each install with confidence.
Rechargeable Li-on battery lasts approximately 3.5 hours on a full charge. If the battery runs low
during use, you can loop the satellite receiver through the meter and power the meter from the satellite
receiver power supply. Meter housing has a battery door for easy access and replacement of the battery.
Comes with a Ruff Neck protective jacket to protect your meter on the job.
Universal charger operates on 120vac/60Hz or 220vac/50Hz
making it usable anywhere. Easy change power plug.
Preset Global Satellite Data Bank
User Defined Satellite Data Bank
Wide, Clear, Easy to Read LCD
All Parameters show on one screen
Easy to Learn
Easy Operation
Keypad Editing
Switchable Back Light
Internal Power Supply
Can be powered from the satellite receiver
Universal Charger, 120vac 60Hz / 220vac 50 Hz
12vdc Car Charger
True USB interface
Replaceable F-81 connectors
Ruff Neck protective jacket
Cost Effective
Input Frequency Range: 950~2150MHz
Signal field intensity range: 30dBuV-105dBuV
Measurement Unit: dBmV,dBµV, dBm
Measurement Accuracy: ±1.5dB
Input Resistance: 75 ohm
Symbol Rate: 2Msps-45Msps
Connector: F type
Measurement type: signal strength,bit error rate,S/N
QPSK switch: automatic identification
22K control: supported
Audio-output: Speaker
Display: Code segment wide-temperature LCD
Memory content: 300 reserved locations for global satellite channels,
100 user-defined channels
LNB Power Supply: 13V, 18V, <500mA
Interface mode: USB
Adapter power supply: AC100V~240V
C input: DC12~23V
Output port voltage: DC12-23V
Battery working time: about 2.5 hours continuously after full charge,
varying from LNB with different power consumption.
3.5 hours or more in normal use.
Charging time: 4 to 6 hours.
Working Temperature: 0°C~40°C
Storage Temperature: -10°C~50°C
Exterior size: 142x82x35(mm)
AC adapter
1 pc
Car charger 1 pc
RF connector 2 pcs
USB cable 1 pc
User manual 1 pc
Li-ion battery 1 pc
