sliding garage door

DEC:4" Pulley
The pulley is made of 2 times 1.2mm cold rolled
steel riveted together,6 rivets proportionally spaced
lnner ring heat treated

DEC:Residential Inside Slide Latch
Include cases,bar,spring and screws
Case:2mm steel. Bar:4mm steel
The center line of the fixing holes is 8

PUSHER SPRINGS 15"
12 GAUGE BRACKET WITH MOUNTING SLOTS
ZINC PLATED STEEL TOTAL LENGTH: 15".6" COMPRESSION

BUSHING, FLAGED NYLON 1" BORE 2" OD INNER RACE OFFSET : 7/32" FROM BEARING PLATE FOR CENTER SUPPORT ONLY

Description: Porosity Bottom Bracket
The bracket has left and right sides
Thickness:2.3 mm, Finish: zinc plated

2" SEALED NYLON ROLLER WITH ZINC PLATED STEM
4" STEM ( WORKING LENGTH=3 1/4" )
BULGED SHOULDER
WHITE NYLON TIRE FOR QUIET OPERATION

4#Hinge
GDP1004
DEC:3#Hinge
Thickness:1.8mm
For use with 11mm diameter roller...

Residential Top brackets
For use with double track door and suitable for 11mm shaft
Thickness:2.5mm
Finish:zinc plate

Adjustable top rollers
top bracket with rollers
bright zinc plated 12 Gauge, 2" 11 ball nylon rollers
roller rating :75 lb load@15000 12" door cycl

USE ON NON INSULATED DOOR PANELS
3" INSIDE DIAMETER
INCLUDES FASTENER & GASKETS

Industrial top Bracket
The bracket is provided with an assembled roller slides and suitable for residential overhead doors.
Thickness:1.5m

6#Hinge
GDP1004
DEC:6#Hinge
Thickness:1.8mm
For use with 11mm diameter roller...

2" 10 BALL STEEL ROLLER WITH ZINC PLATED STEMS
4" STEM ( WORKING LENGTH=3 1/4" )
BULGED SHOULDER

DEC:S HOOK
GARAGE DOOR INSTALL PARTS
Finish: Zinc plate

DEC:U HOOK
GARAGE DOOR INSTALL PARTS
Finish: Zinc plate

STANDARD LIFT - CABLE DRUM 18' 3 screw
DOOR HEIGHT:18' 1"
RATED LIFTING WEIGHT PER DRUM:750 LBS
MAXIMUM CABLE DIAMETER:3/16" (5mm
GDP Intern

Lengthen Double Track Top Bracket
For use with double track door and suitable for 11mm shaft
Thickness:3mm
Finish:zinc plate

DECShaft Coupler
The coupler is made of cast Iron.
the couplers flanges are attached together by three 3/8 inch bolt and nut

DEC:Left & Right Bearing Bracket
The bearing bracket is provided with a 1 Inch bearing installed.
Suitable for residential

STANDARD LIFT - CABLE DRUM 18'MAXIMUM DOOR HEIGHT:18' 1"
RATED LIFTING WEIGHT PER DRUM:750 LBS
MAXIMUM CABLE DIAMETER:3/16" (5mm)

2"Safe Bottom Bracket
(unadjustable)
DEC: 2"Safe Bottom Bracket (unadjustable)
The devise is suitable for 2"tracks,the advised max door weight is 7

Adjusstable Bottom Bracket
DEC:Adjusstable Bottom Bracket
The bearing bracket is provided with a 1"bearing install
Both left and right available

164 Hi lift cable drum
164 HI-LIFT
Max. Hi-lift: 164"
Capacity: 1000 lbs per drum
Max.cable size: 1/4"

6" Spring Fitting
1" bore(1-1/4"bore use parts#1404)
single thread for LH&RH wound springs
Maximum wire size- 4375" diameter
set includes(2)wind

Double Track Top Bracket
DEC :Double Track Top Bracket
For use with double track door and suitable for 11mm shaft
Thickness:3mm
Finish: zinc plate

Lengthen Double Track Top Bracket(Bending)
For use with double track door and suitable for 11mm shaft
Thickness:3mm
Finish:zinc plate

BRIGHT CHROME PLATED

18 cable drums
Max.door height 8'1"
Rated lifting weight per drums 500 LBS

2"Safe Bottom Bracket
(unadjustable)
DEC: 2"Safe Bottom Bracket (unadjustable)
The devise is suitable for 2"tracks,the advised max door weight is 7

DEC:Commercial Inside Slide Latch
Include cases,bar,spring and screws.
Case:1.5mm steel. Bar:4mm steel.
The center line of the fixing holes is 102