Dual-band mobile phone signal booster ST-92B Max coverage 1000m2
What is mobile phone signal booster?
Cell phone signal booster is also called repeater, amplifier, which is a products designed to solve the mobile phone blind signal. As the mobile phone signal is transmitted by electromagnetic waves to establish a communications link, the building of the barrier, in some tall buildings inside, the basement of some places such as malls, restaurants, places of entertainment such as karaoke OK sauna and massage, underground civil air defense projects, subway stations and many other places where cell phone signals can not reach and can not use the phone. Cell phone signal amplifier can solve these problems in a particular place as long as the installation of a mobile phone signal amplifier system, the entire range of mobile phone signals can be well used, staff or customers will get great convenience.
Application places of signal boosters
1. For large buildings such as stores, offices, school, company headquarters, warehouse and so on
2. For small Houses that in remote place
3. For vehicle (Car, Truck, RV…)
4. For public place, for example: Metro, Tunnel, Hotel, Pub, Supermarket, etc
5. Gas Station, Gas Filled Station, Oil Field, Oil Depot
Main Specifications:
Specifications | Uplink | Downlink | Bandwidth |
Frequency Range: GSM | 890~915Mhz | 935~960Mhz | 25MHZ |
DCS | 1710~1780Mhz | 1805~1880Mhz | 70MHZ |
WCDMA-3G | 1920~1980mhz | 2110~2170Mhz | 60MHZ |
Max Gain | 75dB | 80dB | |
Output Power | 10dBm /14dBm | 14dBm / 17dBm | |
Noise Figure @ max. gain | 8dB | 14dB | |
Max. Input Power Without Damage | 0dBm | ||
Ripple in Band | ≦8dB | ||
Return loss | ≦-8 dB | ||
Auto Level Control | 30dBm | ||
MGC | 31db@1dB/step | ||
Time Delay | ≦0.5 μs | ||
MTBF | ＞ 20000 hours | ||
Power Supply | AC:110~240V, 50Hz/ 60Hz;DC:5V 3A | ||
Power Consumption | 12.5W | ||
Impedance | 50 Ω | ||
RF Connector | N -Female | ||
Cooling | Heat sink Convection cooling | ||
Dimensions (D x W x H ) | 256X206.91X57.3(mm) | ||
Weight | 2.9KG | ||
Installation Type | Wall Installation | ||
Environment Conditions | IP40 | ||
Humidity | < 90% | ||
Operating Temperature | -10℃ ~ 55℃ | ||
The full set may include (the accessories is up to your choice)
ST repeater main unit
◆Outdoor antenna
◆Indoor antenna
◆Feeder line
◆Power Splitter (when there are more than 2 indoor antennas)
◆Connector(N connector, F connector, N to F connector etc)
Installation guide:
Installation Steps
1 Use of mobile phones at the top of building or around the building to check out the direction of the strongest signal location.
2 Select the appropriate location, and put the outdoor antenna fix to the wall or bracket.
3 Select the appropriate location of the indoor locations (this location could be best that close to power and a well-ventilated place, sun-proof, rain-proof) Install the Indoor Repeater, and fix on wall or bracket.
4 Put the outdoor antenna to the "OUT DOOR" connector and tightens it. Thus complete the outdoor antenna and Repeater's connection.
5 After setting the suitable location of the indoor antenna and the installation place, then fixing the antenna.
6 The indoor antenna and Repeater wiring, the indoor antenna connect one end of the interface and on the other end connect Repeater's "IN DOOR" port.
Adjusting illustration
A Proper adjustment of the antenna's position so that the best communication quality and signal strength.
B Indoor antenna installed location should stay away from one end of the outdoor antenna, so as not to interfere with each other. (The outdoor antenna away from the indoor antenna placed above a layer of floor is better)
C Indoor antenna should be installed above the height of 2 m of the ceiling or the corner.
D Using the waterproof tape to wrap where has connector, so as to avoid oxidation caused by moisture, resulting in reduced indoor signal coverage.
