Multifuncion dimmable led driver 1*30W output current 250-700mA 1-10V and Push 103*67*22 for led panel ligth
Description:
1, ML30C-PV is multi-current and multi-voltage supply. selection of output current and voltage
through DIP switch
2, Output current and output voltage can be set by DIP switches, constant output current range from 350mA to 1050mA. Also, the LED driver supply 12Vdc / 24Vdc output voltage for you selection.
3, 12Vdc /24Vdc is not constant voltage strictly, it is a limit that the output voltage will not exceed 12Vdc /24Vdc when output 700mA. So the output road range
by 12Vdc( 0-700mA )is 8.4W max.
4. with 1-10V and push button
5, With top circuit design, AC-DC-DC, no flicker.
6, Jumper design for switching different dimming modes, it is very convenient to select suitable
dimming function as you required.
7, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the
same switch. This means there is no need for any additional synchrony wire in larger installations,
where many drivers should be controlled by one switch.
8, Memory function: The driver has built-in permanent memory against power failure. Lights can
return to previous dimming level when switch off and on again, even at mains restores.
9, Synchronization: thanks to the MCU programme, up to 50pcs drivers should be controlled by the
same switch. This means there is no need for any additional synchrony wire in larger installations,
where many drivers should be controlled by one switch.
10, Maximum length of the cable, from switch to last driver is 20m.
11, Factory setting: 100% dimming level and 250mA output.
12, Reset the LED dirver easily by a jumper.
13, Protection: Short circuit / Over voltage / Over temperature.
14.1, 5 years guaranty
Applications:
For led panel light, led highbay, led strip etc.
Synchronization:
For the resynchronization to work correctly when more than one driver is connected to the same
push button, follow steps of below after the drivers are connected:
A) Press push button for more than one second, followed by a short push (<1s), now, led light
switches off.
B) Do a long push, the system will be resynchronized.
Dimming Operation:
A) 1-10V Dim
Using the push dimming will make 1-10V dimming inactivated. The driver has to be reset to active the 1-10V dimming function again.
B) PUSH Dim
Short push (<0.1sec): Ignore, to avoid reaction on AC spike.
Short push (0.1~1sec): Switch on or switch off.
Long push (>1sec): Dimming up or down, dimming level automatically stops at minimum or maximum value.
Specifications
|
INPUT
|
Input voltage |
220-240Vac |
|
Input frequency |
50-60Hz |
|
|
Input current |
0.16A max |
|
|
Power factor |
≥0.90 |
|
|
Efficiency(Note1) |
≥85% |
|
|
Leakage current |
0.5mA/240Vac |
|
|
OUTPUT
|
Output current/voltage and load |
250mA 16-60V DC 15W max 350mA 16-60V DC 21W max 400mA 16-60V DC 24W max 450mA 16-60V DC 27W max
Channel: madeinchina.hisupplier.com - hebei.hisupplier.com - ningbo.hisupplier.com Language Option:
العربية -
Nederlands-
Français-
Deutsch-
Italiano-
日本語-
한국의-
Português-
Pусский-
Español
IPR Protection Policy -
Terms of Use -
Privacy Policy -
Security Measures
Copyright © HiSupplier.com Online Inc. All Rights Reserved. |
