HPR130 / HPR130XD Hypertherm Plasma Cutter Consumables For Plasma Cuttting
We can offer you all plasma consumables for hyptertherm, Kjellberg, Esab, Koike, Komatsu, Thermadyne, such as: electrode, nozzle, shield, swirl ring, inner cap, retaining cap, water tube, torch body and so on.
Each of our products has been tested with a rigorous precision instrument, A large number of piercings tests and service life tests, And made batch trial in our customers. If all results are good, then we will producing them.
| Machine | HEC NO. | Ref NO. | Description |
|
HSD 130 |
H03528 | 220528 | Electrode,(Air)45/(Oxygen)50Amp |
| H02487 | 220487 | Electrode,(Air)130/(Oxygen)130Amp | |
| H03415 | 220415 | Electrode,130Amp (N2,H35) | |
| H73529 | 220529 | Swirl Ring,(Air)45/(Oxygen)50Amp | |
| H72488 | 220488 | Swirl Ring,(Air)130/(Oxygen)130Amp | |
| H13525 | 220525 | Nozzle,45Amp (Air) | |
| H13530 | 220530 | Nozzle,50Amp (Oxygen) | |
| H13492 | 220492 | Nozzle,130Amp (Air) | |
| H13489 | 220489 | Nozzle,130Amp (Oxygen) | |
| H13535 | 220535 | Nozzle,130Amp (N2,H35) | |
| H33578 | 220578 | Retaining Cap 45/50/130Amp (Air,Oxygen) | |
| H33534 | 220534 | Retaining Cap 45/130Amp (N2 and F5,H35) | |
| H23532 | 220532 | Shield,(Air)45/(Oxygen)50Amp | |
| H22536 | 220536 | Shield,130Amp (Air) | |
| H22491 | 220491 | Shield,130Amp (Oxygen) | |
| H03415 | 220415 | Electrode,130Amp (N2,H35) | |
| H03535 | 220535 | Nozzle,130Amp (N2,H35) | |
| H33534 | 220534 | Retaining Cap 45/130Amp (N2 and F5,H35) |
Technical Support:
The problem of plasma cutting
5.1 no high frequency guidance arc
Check high frequency arc ignition circuit, first check the 110VAC, and observe the G1, G2 whether there is discharge sparks exist. If not, generally 110VAC did not come or fixed G1, G2 plastic board damp, damp after G2, G1 can not discharge and produce high pressure. Drying wood glue with a hair dryer to restore 110VAC. If there is still no guide arc, should check the high frequency arc, due to the high frequency of the skin effect, the high frequency line and the nozzle of the conductive ring is not good or because of the reasons for the sealing ring and the cooling water will not have a short circuit. Open the cutting gun, tighten the high frequency line or replace the sealing ring, generally can solve the problem.
5.2 there is no cutting arc
In the case of a high frequency spark observed, first check whether there is an open circuit voltage 400VDC. If not, check whether the phase of the three-phase power supply. High power silicon controlled rectifier and trigger circuit board in power supply box. If the power supply is normal, open the PLC control box, check the PLC input and output signals. The input consists of cooling water, cutting water flow signal, nitrogen and oxygen pressure signal. Cutting water flow signal without cooling water, cooling water pump should be replaced, without cutting the pump; nitrogen, oxygen pressure signal should be tested for nitrogen, oxygen source, and check whether the pipeline leaks. Such as the start conditions are met, will have to check the cutting gun, electrode rod sealing ring or the nozzle seal damage will water seeping into the cavity between the electrode and nozzle, leading to short-circuit DC power supply and the nozzle, can not form a loop with the workpiece. Replace the sealing ring, re assembled torch that can solve the problem.
