Product Feature
1 High Cost-effective, Ultra Low Noise
2 Motor and drive heating is low
3 Supply voltage can achieve 50VDC
4 Output current peak can achieve 8.3A(average 5.8A)
5 Input signal TTL compatible, current automatically reduce to half in stationary
6 Three-phase stepper motor which has 3 or 6 wire can be driven
7 Optical isolation differential signal input
8 Impulse frequency response can achieve 400KHz
9 Up to 8 kinds of subdivide
Product Overview
3MD560 is a latest high subdivision three-phase stepper motor drive, suitable for drive 57-86 seat NO of various brands three-phase stepper motor. Drive use advanced sine current control
Technology, so it obviously improved the noise and riding stability of motor. Compared with most other subdivision drive products on the market, the calorific value of 3MD560 drive and motor reduce more than 15%-30%. Drive and three-phase stepper motor can improve position control accuracy, so particularly suitable for low noise, low heating motor, occasions with high stability and high requirements.
Main Application Fields
Suitable for all kinds of small and medium-sized automation equipment and instruments, such as engraving machine, marking machine, cutting machine, laser typesetting, plotter, numerically controlled machine tools, automatic assembly equipment, etc. The application effect is very good for little noise and high speed equipment.
Electrical Specification
| Introductions | Unit | Minimum | Typical Value | Maximum |
| Output Current | A | 2.1 | - | 8.3 |
| Input Power Voltage | VDC | 18 | 36 | 50 |
| Control Signal Input Current | mA | 7 | - | 16 |
| Stepper Pulse Frequency | KHz | 0 | - | 400 |
| Pulse Low Level Time | μs | 1.2 | ||
| Insulation Resistance | MΩ | 500 |
Working Current Setting
| Output Effective Value Current | SW1 | SW2 | SW3 |
| 1.35A | off | off | off |
| 1.86A | on | off | off |
| 2.60A | off | on | off |
| 3.20A | on | on | off |
| 3.80A | off | off | on |
| 4.45A | on | off | on |
| 5.20A | off | on | on |
| 5.80A | on | on | on |
Micro-step Subdivide Setting
| steps/rev | SW5 | SW6 | SW7 | SW8 |
| 200 | off | off | off | off |
| 400 | on | off | off | off |
| 500 | off | on | off | off |
| 800 | on | on | off | off |
| 1000 | off | off | on | off |
| 1250 | on | off | on | off |
| 1600 | off | on | on | off |
| 2000 | on | on | on | off |
| 2500 | off | off | off | on |
| 3200 | on | off | off | on |
| 4000 | off | on | off | on |
| 5000 | on | on | off | on |
| 6400 | off | off | on | on |
| 8000 | on | off | on | on |
| 10000 | off | on | on | on |
| 12800 | on | on | on | on |
Control Signal interface Description
| Name | Function |
| PUL+(+5V) | Pulse control signal: pulse rising edge valid; PUL- high level 4-5V, low level 0-0.5V. In order to reliably respond pulse signal, pulse width should be more than 1.2μs. Using +12V or +24V, it needs to cascade resistance. |
| PUL-(PUL) | |
| DIR+(+5V) | Direction Signal: high/low level signal, in order to ensure motor to reliable reversing, direction signal should be built before pulse signal at least 5μs. The initial direction of motor be concerned with motor's wires, exchanging any two of three-phase winding U,V,W can change initial running direction of motor, DIR- high level 4-5V, low level 0-0.5V. |
| DIR-(DIR) | |
| ENA+(+5V) | Enable signal: The input signal is used as enable or forbid. ENA+ connect 5V, ENA- connect low level(or internal light coupling conduction),drive will cut off any phase current of the motor, which no respond stepper pulse. If you don't need the function, keep dangling enable signal. |
| ENA-(ENA) |
Power and motor interface description
| Name | Function |
| GND | DC Power Ground |
| +V | DC power positive pole, +18V-+150V any value is OK, but recommended value is about +36VDC. |
| U | Three-phase motor U phase |
| V | Three-phase motor V phase |
| W | Three-phase motor W phase |
