Descriptions:
Process: Injection Molded Size Range: dn50 to dn1600
SDR avialable:SDR11-SDR26 Material:PE100 (PE80 on request) Sabic/Borouge/Sinopec
Dimensions:
d(mm) | D(mm) | D1(mm) | H (mm) | L (mm) | SDR |
900 | 1005 | 944 | 75 | 245 | 13.6 |
900 | 1005 | 944 | 70 | 245 | 17 |
1000 | 1110 | 1047 | 80 | 250 | 13.6 |
1000 | 1110 | 1047 | 75 | 250 | 17 |
1200 | 1330 | 1230 | 80 | 260 | 17 |
1200 | 1330 | 1230 | 75 | 260 | 21 |
1400 | 1535 | 1440 | 80 | 170 | 21 |
1400 | 1535 | 1440 | 70 | 170 | 26 |
1600 | 1760 | 1650 | 85 | 170 | 26 |
Note: 1, All dimensions are subjected to be changed without notice. For enginnering use,please contact with us for details.
2, Other sizes are available on request.
3,To allow full disc opening for the
butterfly valve, a corner chamfer is required
to be machined on the stub end face.Contact
us for consultant on the detailed design of
this special stub end.
4, A stub end is usually used together with a flange, and the dimensions of the coppresponding flange should be taken into account carefully to avoid any mismatch between them.
White color availble on request. All stub ends machined after injection
Laser printing Stub End Stocking for fast delivery
Main Characteristics
BESFUSION molded butt fusion fittings stub end are produced from 100% virgin Polyethylene material of PE100,produced by Sabic, Borouge and Sinopec, the leading Polyethylene manufacturers in the world. All BES butt fusion fittings stub end are compatible for heat fusion with any pipe or fittings manufactured from a like or similar resin.
Butt fusion fittings produced by BESFUSION have been approved to be in compliance with ISO4427 and BS EN 12201 standards, with the main properties as below
Material Properties | Unit | Test Method | Value |
Density PE100 | g/cm³ | ISO 1183-2 | 0.957～0.963 |
Density PE80 | g/cm³ | ISO 1183-2 | 0.93～0.95 |
OIT | min | ISO11357-6 | ＞20 |
MFR | g/10ming | ISO 1133:2005, Condition T | 0.25～0.44 |
Butt Fusion Fittings Properties | Test Method | Performance |
Hydrostatic Strength at 20℃ 100hs | ISO1167-1 ISO 1167-3 | No failure |
Hydrostatic Strength at 80℃ 65hs | ISO1167-1 ISO 1167-3 | No failure |
Hydrostatic Strength at 80℃ 1000hs | ISO1167-1 ISO 1167-3 | No failure |
Tensile strength | ISO 13953 | Ductile Failure |
OIT | ISO11357-6 | ＞25 minutes |
MFR Change | ISO1133:2005, Condition T | Within 20% |
Factory Corner
Our Products
HDPE Pipes:dn20 to dn1600
Socket Fusion Fittings:dn20 to dn110
Molded Butt Fusion Fittings:dn50 to dn 315,SDR11; dn355 to dn630,SDR17
Electrofusion Fittings:dn20 to dn 630
PP Compression Fittings
Steel Flanges,PP/ST Flanges
Fabricated Fittings: dn110 to dn 1600
