Waterproof Ceramic Wall Tile Adhesive

Trade on HiSupplier, Worry Free Guarantee
Trading safety, secure your money, lower the risk, protect both buyers and suppliers
HiSupplier is a Chinese multinational company in U.S, it helps to coordination and order landing.
More ›
  • Product Details
  • Company Profile
  • Product Reviews


Swimming Pool Ceramic Wall Tile Adhesive Water Proof 300×300mm



PB-106 is a kind of high quality environment-friendly waterborne powder which can be mixed with water and used for bonding ceramic tile on the surfaces of wall, ground and floor. It is easily applied and can achieve an excellent adhesion..





PB-106 is a kind of synthetic rubber latex, mixing with the ceramic tile adhesive (premixed graded fine sand, special additives and synthetic resin) to form a high viscosity achieve, which can be used in all kinds of construction surface. PB-106 can also be mixed with  sand and cement. The adhesive can harden without obvious shrinkage. It will not slip off when pasting a heavy ceramic tile in the vertical surface.



Operation Process:


1, Substrate Preparation


1) The substrate surface should be firm, dry and clean, no grease, no wax, or other loose materials.

2) The cement surface should not be shrinking after pasting the ceramic tile.

3) Each 1cm-thick plastering should be maintained at least 1 week.

4) Cooling the substrate when it is too hot.



2, Application of Adhesive:


1) Use a notched trowel to paste the adhesive. The general principle of choosing a correct trowel is that the coverage in the interior wall and lightloading area is at least 65~70%, while 100% in the exterior wall and overloading area.

2) Paste one layer on the surface with the flat surface of the trowel to reach a high-bond-strength effect, then choose the size of the notched trowel according to the size and type of the ceramic tile.


Typical ceramic tile

Mosaic size≤5×5cm

Normal ceramic tile

Ground,plane, or the ceramic tile uneven

Pinbangnotched trowel type

SquareNo.4, about 2~2.5kg/

TypeV No.5, about 3kg/

TypeV No.6, about 5kg/


In demanding situations, such as the 300×300mm ceramic tile in exterior wall, ground, swimming pool and pool, and the ground which is overloading or need to be polished, just paste the adhesive evenly on the back of the ceramic tile(dorsal division).



3, Lay-up Ceramic tile:


1) No need to wet the ceramic tile and stone before laying, unless there is much dust on the back of the ceramic tile.

2) In order to maintain a good contact with adhesives, the ceramic tile should be pressed hard in place.

3) The open assembly time of PB-106 in normal temperature and humidity is about 20 minutes. In the conditions of adverse climatic (burning sun, dry wind, high temperature, etc.) or strong water-absorption of the surface, open assembly time may be shortened, sometimes reduced to a few minutes. So always check carefully whether the adhesive surface peeling, or whether it is still in a sticky situation. If it is peeling already, pasting the adhesive one more time. Wetting the surface before pasted the adhesive helps to extend the  open assembly time.

4) Wetting the adhesive when it is peeling is not recommended, or it would form a nonstick film instead of dissolving.

5) If necessary, the seam should be adjusted within 60 minutes after laying bricks.

6) It can not be washed or in the rain within 24 hours after laying bricks, and avoid placing in cold or exposed situation for 5~7 days.



4, Jointing:


1) Fill the wall seam with Pinbang special cement base or epoxy grout after laying 4~8 hours while fill the floor seam after laying 24 hours. And there are many kinds of color of grout can be choosed.

2) Use Pinbang grout to fill the crack.

3) Available for walking: about 24 hours after laying.

4) Available for use: the surface can be used about 14 days later while the swimming pool 21 days later.



5, Cleaning:


Tools can be cleaned with plenty of water before the Pinbang Super Tile Adhesive (C2 standard) dried, or cleaning will be difficult, but it still can be cleaned with Pinbang cleaner.



Store Method:


Store in cool and dry place, unopened product can be saved for one year.






Send message to this supplier
Mr. Deng
Tel: 86-020-8800230
Enter between 20 to 3,000 chatacters.
Contact Method
Guangzhou Honghe Building lndustrial co.,LTD
Zhongshan Avenue, Tianhe District,, Guangzhou, Guangdong, China (Mainland)
Didn't find what you're looking for? Post Buying Lead or contact our customer service specialist for help!
Buyer Help Center